Arduino入门教程—拓展实验篇九驱动单色8*8点阵

AllBlue · 发表于 2013-8-18 15:21:31

驱动单色8*8点阵

本次实验使用Arduino 控制器直接驱动一个单色的8*8点阵，所用点阵型号为LD-1088BS，如下图：

登录/注册后可看大图

点阵图片.jpg (63.2 KB, 下载次数: 126)

下载附件

2013-7-6 20:44 上传

内部原理图：

登录/注册后可看大图

LED dot matrix.jpg (99.28 KB, 下载次数: 136)

下载附件

2013-7-6 20:37 上传

实际引脚编号：

登录/注册后可看大图

实际引脚编号.jpg (55.24 KB, 下载次数: 133)

下载附件

2013-7-17 19:33 上传

Arduino连接图：

登录/注册后可看大图

点阵电路图.jpg (97.44 KB, 下载次数: 134)

下载附件

2013-7-6 20:30 上传

程序所用扩文件：

FrequencyTimer2.zip (4.55 KB, 下载次数: 942)

2013-7-6 20:19 上传

点击文件名下载附件

例程：

[C] 纯文本查看 复制代码

/*
* Show messages on an 8x8 led matrix,
* scrolling from right to left.
*
* Uses FrequencyTimer2 library to
* constantly run an interrupt routine
* at a specified frequency. This
* refreshes the display without the
* main loop having to do anything.
*
*/

#include <FrequencyTimer2.h>

#define SPACE { \
    {0, 0, 0, 0, 0, 0, 0, 0},  \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0} \
}

#define H { \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 1, 1, 1, 1, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}  \
}

#define E  { \
    {0, 1, 1, 1, 1, 1, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 1, 1, 1, 1, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 1, 1, 1, 1, 1, 0}  \
}

#define L { \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 1, 1, 1, 1, 1, 0}  \
}

#define O { \
    {0, 0, 0, 1, 1, 0, 0, 0}, \
    {0, 0, 1, 0, 0, 1, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 0, 1, 0, 0, 1, 0, 0}, \
    {0, 0, 0, 1, 1, 0, 0, 0}  \
}

byte col = 0;
byte leds[8][8];

// pin[xx] on led matrix connected to nn on Arduino (-1 is dummy to make array start at pos 1)
int pins[17]= {-1, 5, 4, 3, 2, 14, 15, 16, 17,13, 12, 11, 10, 9, 8, 7, 6, };

// col[xx] of leds = pin yy on led matrix
int rows[8] = {pins[16], pins[15], pins[11], pins[6], pins[10], pins[4], pins[3], pins[13]};

// row[xx] of leds = pin yy on led matrix
int cols[8] = {pins[9], pins[14], pins[8], pins[12], pins[1], pins[7], pins[2], pins[5]};

const int numPatterns = 6;
byte patterns[numPatterns][8][8] = {
  H,E,L,L,O,SPACE
};

int pattern = 0;

void setup() {
  // sets the pins as output
  for (int i = 1; i <= 16; i++) {
    pinMode(pins[i], OUTPUT);
  }

  // set up cols and rows
  for (int i = 1; i <= 8; i++) {
    digitalWrite(cols[i - 1], LOW);
  }

  for (int i = 1; i <= 8; i++) {
    digitalWrite(rows[i - 1], LOW);
  }

  clearLeds();

  // Turn off toggling of pin 11
  FrequencyTimer2::disable();
  // Set refresh rate (interrupt timeout period)
  FrequencyTimer2::setPeriod(2000);
  // Set interrupt routine to be called
  FrequencyTimer2::setOnOverflow(display);

  setPattern(pattern);
}

void loop() {
    pattern = ++pattern % numPatterns;
    slidePattern(pattern, 60);
}

void clearLeds() {
  // Clear display array
  for (int i = 0; i < 8; i++) {
    for (int j = 0; j < 8; j++) {
      leds[i][j] = 0;
    }
  }
}

void setPattern(int pattern) {
  for (int i = 0; i < 8; i++) {
    for (int j = 0; j < 8; j++) {
      leds[i][j] = patterns[pattern][i][j];
    }
  }
}

void slidePattern(int pattern, int del) {
  for (int l = 0; l < 8; l++) {
    for (int i = 0; i < 7; i++) {
      for (int j = 0; j < 8; j++) {
        leds[j][i] = leds[j][i+1];
      }
    }
    for (int j = 0; j < 8; j++) {
      leds[j][7] = patterns[pattern][j][0 + l];
    }
    delay(del);
  }
}

// Interrupt routine
void display() {
  digitalWrite(cols[col], LOW);  // Turn whole previous column off
  col++;
  if (col == 8) {
    col = 0;
  }
  for (int row = 0; row < 8; row++) {
    if (leds[col][7 - row] == 1) {
      digitalWrite(rows[row], LOW);  // Turn on this led
    }
    else {
      digitalWrite(rows[row], HIGH); // Turn off this led
    }
  }
  digitalWrite(cols[col], HIGH); // Turn whole column on at once (for equal lighting times)
}

显示图片为“HELLO ”滚动显示！

Arduino直接驱动8*8点阵占用的I/O口太多，所以建议大家使用芯片驱动8*8点阵，例如74HC595或者MAX7129芯片！！

下面也为大家提供一些IC资料，有兴趣的可以研究研究~~

74HC595中文资料：

74HC595的中文版资料.pdf (2.11 MB, 下载次数: 2919)

anjiao · 发表于 2015-7-22 02:23:08

我补一个驱动5针LED的例子
D:\Documents\Bluetooth Folder\IMG_20150722_021849.jpg

[C++] 纯文本查看 复制代码

#include <FrequencyTimer2.h>

#define NOP() do { __asm__ __volatile__ ("nop"); } while (0)
#define _countof(a)		(sizeof(a) / sizeof(a[0]))

class HC595LED
{
public:
	HC595LED(int ser, int rck, int srck)
	{
		_SER = ser;
		_RCK = rck;
		_SRCK = srck;
	}
	
	void begin()
	{
		pinMode(_SER, OUTPUT);
		pinMode(_RCK, OUTPUT);
		pinMode(_SRCK, OUTPUT);

		digitalWrite(_SER, LOW);
		digitalWrite(_RCK, LOW);
		digitalWrite(_SRCK, LOW);
	}

	void displayRow(uint8_t nRow, uint8_t data)
	{
		nRow = 7 - nRow;

		for(int i = 0; i < 8; i++)
			_rowEnable(i == nRow);
		for(int i = 7; i >= 0; i--) {
			_colEnable(bitRead(data, i));
		}
		flushScreen();
	}

	void clear()
	{
		for(int i = 0; i < 8; i++) 
			_rowEnable(false);
		for(int i = 0; i < 8; i++)
			_colEnable(false);
	}

	void writeItem(bool bHigh)
	{
		digitalWrite(_SER, bHigh ? HIGH : LOW);
		_flushItem();
	}

	void flushScreen()
	{
		digitalWrite(_RCK, HIGH);
		NOP();
		NOP();
		digitalWrite(_RCK, LOW);
	}
private:
	void _rowEnable(bool bEnable)
	{
		writeItem(!bEnable);
	}
	void _colEnable(bool bEnable)
	{
		writeItem(bEnable);
	}

	void _flushItem()
	{
		digitalWrite(_SRCK, HIGH);
		NOP();
		NOP();
		digitalWrite(_SRCK, LOW);
	}

private:
	int _SER;
	int _RCK;
	int _SRCK;
};

///////////////////////////////////////////////////////////////////////

//Pin connected to DS of 74HC595
const int SER_PIN = 8;
//Pin connected to ST_CP of 74HC595
const int RCK_PIN = 9;
//Pin connected to SH_CP of 74HC595
const int SRCK_PIN = 10;

HC595LED led(SER_PIN, RCK_PIN, SRCK_PIN);

PROGMEM const char SPACE[] = 
{
	0b00000000,
	0b00000000,
	0b00000000,
	0b00000000,
	0b00000000,
	0b00000000,
	0b00000000,
	0b00000000,
};
PROGMEM const char H[] = 
{
	0b01000010,
	0b01000010,
	0b01000010,
	0b01111110,
	0b01000010,
	0b01000010,
	0b01000010,
	0b01000010,
};
PROGMEM const char E[] = 
{
	0b01111110,
	0b01000000,
	0b01000000,
	0b01111110,
	0b01000000,
	0b01000000,
	0b01000000,
	0b01111110,
};
PROGMEM const char L[] = 
{
	0b01000000,
	0b01000000,
	0b01000000,
	0b01000000,
	0b01000000,
	0b01000000,
	0b01000000,
	0b01111110,
};
PROGMEM const char O[] = 
{
	0b00011000,
	0b00100100,
	0b01000010,
	0b01000010,
	0b01000010,
	0b01000010,
	0b00100100,
	0b00011000,
};

const char * const arrShowData[] = {H, E, L, L, O, SPACE};

char arrShowBuffer[] = 
{
	0, 0, 0, 0, 0, 0, 0, 0,
};
void display()
{
	static int s_nIndex = 0;

	led.displayRow(s_nIndex, arrShowBuffer[s_nIndex]);

	s_nIndex++;
	s_nIndex %= 8;
}

void setup() 
{
	led.begin();
    Serial.begin(9600);

    delay(1000);
	led.clear();

	FrequencyTimer2::disable();
	FrequencyTimer2::setPeriod(2000);
	FrequencyTimer2::setOnOverflow(display);
}

void loop() 
{
	int s_nIndex = 0;

	while(true) {
		noInterrupts();
		memcpy_PF(arrShowBuffer, (uint_farptr_t)arrShowData[s_nIndex], sizeof(arrShowBuffer));
		interrupts();

		s_nIndex++;
		s_nIndex %= _countof(arrShowData);

		delay(2000);
	}
}

anjiao · 发表于 2015-7-22 21:30:03

登录/注册后可看大图

limhy1990 · 发表于 2014-11-2 00:08:42

8*8点阵反面5根针的不明白怎么弄。。。求救。。

tiantianyouyou · 发表于 2019-11-12 12:03:46

不错不错，学习一下

wzcc · 发表于 2019-11-5 21:40:58

怎么定义脚位置的？

tiantianyouyou · 发表于 2019-5-2 08:03:41

不错不错，学习一下

tiantianyouyou · 发表于 2019-5-2 08:02:27

MAX7219英文资料，这个好

tiantianyouyou · 发表于 2019-5-2 07:56:40

Arduino入门教程—拓展实验篇九驱动单色8*8点阵

innovater · 发表于 2017-2-10 20:52:42

正在研究74HC595

innovater · 发表于 2017-2-10 18:02:07

有待研究

bearchen · 发表于 2016-10-7 18:24:40

Arduino:1.6.8 Hourly Build 2016/02/16 05:07 (Windows 7), 开发板："Arduino/Genuino Uno"

libraries\FrequencyTimer2\FrequencyTimer2.cpp.o: In function `__vector_7':

C:\Users\Administrator\Documents\Arduino\libraries\FrequencyTimer2/FrequencyTimer2.cpp:42: multiple definition of `__vector_7'

sketch\FrequencyTimer2.cpp.o:sketch/FrequencyTimer2.cpp:42: first defined here

libraries\FrequencyTimer2\FrequencyTimer2.cpp.o: In function `__vector_7':

C:\Users\Administrator\Documents\Arduino\libraries\FrequencyTimer2/FrequencyTimer2.cpp:42: multiple definition of `FrequencyTimer2:

nOverflow'

sketch\FrequencyTimer2.cpp.o:sketch/FrequencyTimer2.cpp:42: first defined here

libraries\FrequencyTimer2\FrequencyTimer2.cpp.o: In function `__vector_7':

C:\Users\Administrator\Documents\Arduino\libraries\FrequencyTimer2/FrequencyTimer2.cpp:42: multiple definition of `FrequencyTimer2::setOnOverflow(void (*)())'

sketch\FrequencyTimer2.cpp.o:sketch/FrequencyTimer2.cpp:42: first defined here

libraries\FrequencyTimer2\FrequencyTimer2.cpp.o: In function `__vector_7':

C:\Users\Administrator\Documents\Arduino\libraries\FrequencyTimer2/FrequencyTimer2.cpp:42: multiple definition of `FrequencyTimer2::setPeriod(unsigned long)'

sketch\FrequencyTimer2.cpp.o:sketch/FrequencyTimer2.cpp:42: first defined here

libraries\FrequencyTimer2\FrequencyTimer2.cpp.o: In function `__vector_7':

C:\Users\Administrator\Documents\Arduino\libraries\FrequencyTimer2/FrequencyTimer2.cpp:42: multiple definition of `FrequencyTimer2::enabled'

sketch\FrequencyTimer2.cpp.o:sketch/FrequencyTimer2.cpp:42: first defined here

libraries\FrequencyTimer2\FrequencyTimer2.cpp.o: In function `__vector_7':

C:\Users\Administrator\Documents\Arduino\libraries\FrequencyTimer2/FrequencyTimer2.cpp:42: multiple definition of `FrequencyTimer2::getPeriod()'

sketch\FrequencyTimer2.cpp.o:sketch/FrequencyTimer2.cpp:42: first defined here

libraries\FrequencyTimer2\FrequencyTimer2.cpp.o: In function `__vector_7':

C:\Users\Administrator\Documents\Arduino\libraries\FrequencyTimer2/FrequencyTimer2.cpp:42: multiple definition of `FrequencyTimer2::enable()'

sketch\FrequencyTimer2.cpp.o:sketch/FrequencyTimer2.cpp:42: first defined here

libraries\FrequencyTimer2\FrequencyTimer2.cpp.o: In function `__vector_7':

C:\Users\Administrator\Documents\Arduino\libraries\FrequencyTimer2/FrequencyTimer2.cpp:42: multiple definition of `FrequencyTimer2::disable()'

sketch\FrequencyTimer2.cpp.o:sketch/FrequencyTimer2.cpp:42: first defined here

collect2.exe: error: ld returned 1 exit status

exit status 1
编译有误。

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

葳蕤礼赞 · 发表于 2016-7-30 20:04:00

Arduino:1.6.10 (Windows 8), 开发板："Arduino/Genuino Uno"

C:\Users\dell-xy\Desktop\sketch_jul30a\sketch_jul30a.ino:1:29: fatal error: FrequencyTimer2.h: No such file or directory

#include <FrequencyTimer2.h>

^

compilation terminated.

exit status 1
为开发板 Arduino/Genuino Uno 编译时出错。

我是五针的,出现这个问题

		自动登录	找回密码
密码			立即注册

Arduino入门教程—拓展实验篇九 驱动单色8*8点阵

Arduino入门教程—拓展实验篇九驱动单色8*8点阵