安卓手机APP蓝牙遥控履带式小车基于Bluetooth 4.0 BLE/2.0 arduino程序

AllBlue · 发表于 2016-8-18 08:18:19

上位机软件方面：
手机安卓APP软件支持蓝牙4.0 及2.0 ，软件介绍及下载地址：http://www.yfrobot.com/thread-11865-1-1.html
软件界面如下，支持重力感应！

controlCar-750.jpg (37.56 KB, 下载次数: 50)

2016-8-16 15:22 上传

硬件方面：
主要器件清单：
1、履带式小车车架 C-Bot
2、arduino UNO R3 兼容控制板 - BlueBird V3
3、PM-R3 电机驱动板
4、4.0低功耗（BLE）蓝牙模块
5、电源 - 7.4V锂电池及充电器
6、超声波模块及舵机云台（未使用，主要实现遥控功能）
组装完成图：

登录/注册后可看大图

履带式小车.jpg (42.68 KB, 下载次数: 60)

下载附件

2016-8-16 16:19 上传

arduino 程序：

[C] 纯文本查看 复制代码

/***
   android app 连接 bluetooth 4.0 ble 实现远程通信
   根据数据指令判断 - 默认小车控制指令：0X70/112，实现局域网遥控功能

   通信数据格式：[$M>](数据头)+[data length] +[code] +[data] +[checksum]
    例1: 24 4d 3e 00 72 72
      24  数据头1   $
      4d  数据头2   M
      3e  数据头3   >
      00  data length 无数据
      72  code  指令
      72  checksum  检验和 除数据头外的数据异或得到
    例2: 24 4d 3e 02 72 64 64 70
      24  数据头1   $
      4d  数据头2   M
      3e  数据头3   >
      02  data length 数据字节数
      72  code  指令
      64  data 1
      64  data 2
      70  checksum  检验和

   连接：(可根据实际情况更改)

   by yfrobot -- [url=http://www.yfrobot.com]www.yfrobot.com[/url]
   24/5/2016
*/
#include <SoftwareSerial.h>
#define DEBUG 1
SoftwareSerial mySerial(12, 11); // RX, TX

#define C_Joystick 112     // Joystick code
#define AIN1 5          // left motor
#define AIN2 6          // left motor
#define BIN1 9          // right motor
#define BIN2 10         // right motor

#define INBUF_SIZE 128
static uint8_t inBuf[INBUF_SIZE];
static uint8_t dataLenght;
static uint8_t checksum;
static uint8_t indRX;
static uint8_t cmdMSP;

uint8_t read8() {
  return inBuf[indRX++] & 0xff;
}

uint8_t readThorttle = 128;
uint8_t readDirection = 128;

void setup() {
  // put your setup code here, to run once:
  Serial.begin(115200);
  mySerial.begin(115200);
  delay(10);

  Serial.println("begin....");
  Serial.println("");

  pinMode(AIN1, OUTPUT);
  pinMode(AIN2, OUTPUT);
  pinMode(BIN1, OUTPUT);
  pinMode(BIN2, OUTPUT);

  mySerial.println("hello world");
}

void loop() {
  // put your main code here, to run repeatedly:
  BleReceive();
  setMotor(readThorttle, readDirection);
}

/**
   evaluate command -- 数据处理
*/
void evaluateCommand() {
  switch (cmdMSP) {
    case C_Joystick:
      readThorttle = read8();
      readDirection = read8();
      //      if (DEBUG) {
      //        mySerial.print("th  - ");
      //        mySerial.print(readThorttle);
      //        mySerial.print("di  - ");
      //        mySerial.println(readDirection);
      //      }
      break;
  }
}

void setMotor(int m1Speed , int dire) //电机驱动函数
{
  if (m1Speed < 128) {
    if ( dire >= 0 && dire < 128) {
      digitalWrite(AIN2, LOW);
      digitalWrite(BIN2, HIGH);
      analogWrite(AIN1, map(dire, 0, 127, 255, 0));
      analogWrite(BIN1, map(m1Speed, 0, 127, 0, 255));
      mySerial.println("forward - left");
    } else if (dire > 128 && dire <= 255) {
      digitalWrite(AIN2, HIGH);
      digitalWrite(BIN2, LOW);
      analogWrite(AIN1, map(m1Speed, 0, 127, 0, 255));
      analogWrite(BIN1, map(dire, 129, 255, 0, 255));
      mySerial.println("forward - right");
    } else {
      digitalWrite(AIN2, HIGH);
      digitalWrite(BIN2, HIGH);
      analogWrite(AIN1, map(m1Speed, 0, 127, 0, 255));
      analogWrite(BIN1, map(m1Speed, 0, 127, 0, 255));
      mySerial.println("forward");
    }
  } else if (m1Speed > 128 ) {
    if ( dire >= 0 && dire < 128) {
      digitalWrite(AIN2, HIGH);
      digitalWrite(BIN2, LOW);
      analogWrite(AIN1, map(dire, 0, 127, 0, 255));
      analogWrite(BIN1, map(m1Speed, 129, 255, 0, 255));
      mySerial.println("back - left");
    } else if (dire > 128 && dire <= 255) {
      digitalWrite(AIN2, LOW);
      digitalWrite(BIN2, HIGH);
      analogWrite(AIN1, map(m1Speed, 129, 255, 0, 255));
      analogWrite(BIN1, map(dire, 129, 255, 255, 0));
      mySerial.println("back - right");
    } else {
      digitalWrite(AIN2, LOW);
      digitalWrite(BIN2, LOW);
      analogWrite(AIN1, map(m1Speed, 129, 255, 0, 255));
      analogWrite(BIN1, map(m1Speed, 129, 255, 0, 255));
      mySerial.println("back");
    }
  } else {
    digitalWrite(AIN2, LOW);
    digitalWrite(BIN2, LOW);
    analogWrite(AIN1, 0);
    analogWrite(BIN1, 0);
    mySerial.print(m1Speed);
    mySerial.print("\t");
    mySerial.print(dire);
    mySerial.print("\t");
    mySerial.println("stop");
  }
}

/**
    receive data function
*/
void BleReceive() {
  uint8_t c;
  static uint8_t dire_offset;
  static uint8_t dataSize;
  static enum _serial_state {
    IDLE,
    HEADER_START,
    HEADER_M,
    HEADER_ARROW,
    HEADER_SIZE,
    HEADER_CMD,
  } c_state = IDLE;
  while (Serial.available() > 0) {
    c = Serial.read();                               // 读串口缓冲区
    if (c_state == IDLE) {                           //串口状态空闲 等待HEADER_START状态的到来
      c_state = (c == '$') ? HEADER_START : IDLE;    //判定是$字符吗？是则进入HEADER_START状态
      if (c_state == IDLE) {}// evaluateOtherData(c); // evaluate all other incoming serial data
    } else if (c_state == HEADER_START) {

      c_state = (c == 'M') ? HEADER_M : IDLE;        //判定是M字符吗？是则进入HEADER_M状态
    } else if (c_state == HEADER_M) {

      c_state = (c == '>') ? HEADER_ARROW : IDLE;    //判定是>字符吗？是则进入HEADER_ARROW状态
    } else if (c_state == HEADER_ARROW) {            //是ARROW字符，进入HEADER_ARROW状态，判定缓冲区的大小
      if (c > INBUF_SIZE) {                          // now we are expecting the payload size 我们期望足够的数据占用缓冲区
        c_state = IDLE;                              //数据位置不够 退出循环
        continue;                                    //不执行该while循环包含的后面的语句，跳出开始下一轮循环
      }
      dataSize = c;
      dataLenght = dataSize;
      dire_offset = 0;
      checksum = 0;
      indRX = 0;
      checksum ^= c;                                 //校验和 1  -  dataSize
      c_state = HEADER_SIZE;                         // the command is to follow 接收到数据长度，进入HEADER_SIZE状态
    } else if (c_state == HEADER_SIZE) {
      cmdMSP = c;                                    //接收 指令(code)
      checksum ^= c;                                 //校验和 2  -  code
      c_state = HEADER_CMD;                          //接收到指令，进入HEADER_CMD状态
    } else if (c_state == HEADER_CMD && dire_offset < dataSize) {
      checksum ^= c;                                 //校验和 3  -  data
      inBuf[dire_offset++] = c;
    } else if (c_state == HEADER_CMD && dire_offset >= dataSize) {
      if (checksum == c) {// compare calculated and transferred checksum
        evaluateCommand();                    //数据处理程序
      }
      c_state = IDLE;                         //返回IDLE状态
    }
  }
}

接收到的数据范围为 0~255，所以程序设定当处于128值时，小车停止。程序下载地址：

yf_ble_Joystick.zip (2.42 KB, 下载次数: 20, 售价: 2 )

UNO · 发表于 2016-9-9 08:56:49

不错的蓝牙控制，有空试一下

tiantianyouyou · 发表于 2019-5-7 16:36:46

谢谢分享~~~~~

		自动登录	找回密码
密码			立即注册

安卓手机APP蓝牙遥控履带式小车 基于Bluetooth 4.0 BLE/2.0 arduino程序

浏览过的版块

安卓手机APP蓝牙遥控履带式小车基于Bluetooth 4.0 BLE/2.0 arduino程序