ESP8266 WiFi

WiFi類

The WiFi class initializes the ethernet library and network settings.

- WiFi.mode()

設置wifi模塊工作模式WIFI_AP,WIFI_STA,WIFI_AP_STA

Wifi AP - WiFi.softAP(ssid,[password],[channel],[ssid_hidden]) 設置AP模式參數 參數 ssid：網路名稱（最長63字元） password：密碼，至少8個字元，NULL為開放網路（可選參數） channel：通道號，1 - 13（可選參數，預設情況下為1） ssid_hidden：網路是否可見，0為可見網路，1為隱藏網路（可選參數，預設情況下為0） 返回值：bool - WiFi.softAPConfig(local_ip,gateway,subnet) 配置AP 參數 local_ip：ap ip(類型：IPAddress-例192,168,0,1) gateway：網關ip(類型：IPAddress) subnet：子網掩碼(類型：IPAddress) 返回值：bool - WiFi.softAPdisconnect(wifioff) 斷開網路，關閉AP - WiFi.softAPgetStationNum() Get the count of the Station / client that are connected to the softAP interface - WiFi.softAPIP() 獲取IP地址，用於AP模式 返回IP地址 - WiFi.softAPmacAddress(mac) 獲取MAC地址，用於AP模式 返回：uint8_t* - WiFi.softAPmacAddress(void) 獲取MAC地址，用於AP模式 返回：String

Wifi STA WL_CONNECTED WL_NO_SSID_AVAIL WL_CONNECT_FAILED WL_IDLE_STATUS WL_DISCONNECTED - WiFi.begin() 開始wifi連接 - WiFi.config(local_ip, gateway, subnet, dns1, dns2) Change IP configuration settings disabling the dhcp client 參數 local_ip Static ip configuration gateway Static gateway configuration subnet Static Subnet mask dns1 Static DNS server 1 dns2 Static DNS server 2 返回：bool - WiFi.reconnect() will force a disconnect and then start reconnecting to AP 返回：bool - WiFi.disconnect(bool wifioff) Disconnect from the network 返回：bool - WiFi.isConnected() 檢查是否已連接 返回：bool - WiFi.setAutoConnect(bool autoConnect) 設置是否複位自動連接，默認自動連接 返回：bool - WiFi.setAutoConnect() 檢查是否設置了複位自動連接 返回：bool - WiFi.setAutoReconnect(bool autoReconnect) 設置當連接斷開時是否重新連接 返回：bool - WiFi.waitForConnectResult() Wait for WiFi connection to reach a result returns the status reached or disconnect if STA is off 返回：連接狀態 WL_CONNECTED WL_NO_SSID_AVAIL; WL_CONNECT_FAILED; WL_IDLE_STATUS; WL_DISCONNECTED; - WiFi.localIP() 獲取IP地址，用於STA模式 返回：IPAddress - WiFi.macAddress(uint8_t* mac) 獲取MAC地址，用於STA模式 - WiFi.macAddress(void) 獲取MAC地址，用於STA模式 - WiFi.subnetMask() Get the interface subnet mask address. 返回：IPAddress - WiFi.gatewayIP() Get the gateway ip address. 返回：IPAddress

- begin()

- disconnect()

- config()

- setDNS()

- SSID()

- BSSID()

- RSSID()

- encryptionType()

- scanNetworks()

- status()

- getSocket()

- macAddress()

Server 類 The Server class creates servers which can send data to and receive data from connected clients (programs running on other computers or devices). - Server - WiFiServer - begin() - available() - write() - print() - println() Client 類 The client class creates clients that can connect to servers and send and receive data. - Client - WiFiClient() - connected() - connect() - write() - print() - println() - available() - read() - flush() - stop() UDP 類 The UDP class enables UDP message to be sent and received. -WiFiUDP -begin() -available() -beginPacket() -endPacket() -write() -parsePacket() -peek() -read() -flush() -stop() -remoteIP() -remotePort()

---

返回ESP8266 Libraries

返回首頁

更多建議和問題歡迎反饋至 YFRobot論壇