磁控传感器:修訂版本之間的差異
出自YFRobotwiki
(以“ 磁控传感器模块 === 产品简介 === <br> 磁控传感器模块是一个发声的电子模块。 === 规格参...”为内容创建页面) |
|||
第 6 行: | 第 6 行: | ||
=== 产品简介 === | === 产品简介 === | ||
<br> | <br> | ||
− | 磁控传感器模块是一 | + | 磁控传感器模块 是采用进口全镀金干簧管设计制作,干簧管(Reed Switch)也称舌簧管或磁簧开关, 是一 种磁敏的特殊开关。它是由Western Electric 公司在1940年 发 明 的 。其它主要元件是开或关的弹性簧片及磁铁或 电 磁铁;经过几十年的改进,它的稳定性更进一步。它寿命可以达到百万次以上。而且干簧管对于坏境的要求也比较低(如不受湿度影响),相对霍尔传感器,它的使用范围更加广。 |
+ | |||
+ | 更多干簧管参数请查看页末 --> 参考资料 。 | ||
第 12 行: | 第 14 行: | ||
=== 规格参数 === | === 规格参数 === | ||
<br> | <br> | ||
− | *供电电压:DC3.3 | + | *供电电压:DC3.3 ~ 5V |
+ | *输入要求:外部磁场 > 5 高斯 | ||
+ | *敏感距离:0 ~ 20mm | ||
+ | *开关电流范围:0 ~ 2A | ||
+ | *开关电压范围:0 ~ 200V | ||
+ | *工作温度范围:-55 ~150℃ | ||
*安装孔径:3MM | *安装孔径:3MM | ||
*模块尺寸:31*21*10.1MM(长*宽*高) | *模块尺寸:31*21*10.1MM(长*宽*高) | ||
第 41 行: | 第 48 行: | ||
:'''示例代码''' | :'''示例代码''' | ||
<pre> | <pre> | ||
− | // | + | // Reed Switch Test |
− | + | ||
− | + | #define ledPin 13 //define LED pin | |
+ | #define reed_switchPin 7 //define reed switch Pin | ||
+ | int reed_switchValue = 0; | ||
void setup() { | void setup() { | ||
− | + | pinMode(ledPin,OUTPUT); | |
− | pinMode( | + | pinMode(reed_switchPin,INPUT); |
− | + | ||
} | } | ||
− | void loop() { | + | void loop() |
− | + | { | |
− | + | reed_switchValue = digitalRead(reed_switchPin); | |
− | + | ||
− | + | if(reed_switchValue == LOW) { | |
− | + | digitalWrite(ledPin,HIGH); // detect the external magnetic field , set the LED on | |
− | + | } | |
− | + | else { | |
− | + | digitalWrite(ledPin,LOW); // or set the LED off | |
− | + | } | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | } | + | |
} | } | ||
</pre> | </pre> | ||
− | 程序下载地址:[http://pan.baidu.com/s/ | + | 程序下载地址:[http://pan.baidu.com/s/1ntu0M3f ReedSwitchTest] |
− | 程序运行结果: | + | 程序运行结果: 当干簧管检测到外部磁场后 , 内部弹片吸合 , 检测到电平,点亮LED,否则熄灭LED 。 |
第 81 行: | 第 79 行: | ||
===参考资料=== | ===参考资料=== | ||
<br> | <br> | ||
− | * [http:// | + | * [http://pan.baidu.com/s/1kTAJU67 干簧管与霍尔传感 器 选择和比较] |
+ | * [http://pan.baidu.com/s/1nttKSXz OKI干簧管手册] | ||
2015年8月29日 (六) 16:51的修訂版本
產品簡介
磁控感測器模塊是採用進口全鍍金干簧管設計製作,干簧管(Reed Switch)也稱舌簧管或磁簧開關,是一種磁敏的特殊開關。它是由Western Electric 公司在1940年發明的。其它主要元件是開或關的彈性簧片及磁鐵或電磁鐵;經過幾十年的改進,它的穩定性更進一步。它壽命可以達到百萬次以上。而且干簧管對於壞境的要求也比較低(如不受濕度影響),相對霍爾感測器,它的使用範圍更加廣。
更多干簧管參數請查看頁末 --> 參考資料。
規格參數
- 供電電壓:DC3.3 ~ 5V
- 輸入要求:外部磁場 > 5 高斯
- 敏感距離:0 ~ 20mm
- 開關電流範圍:0 ~ 2A
- 開關電壓範圍:0 ~ 200V
- 工作溫度範圍:-55 ~150℃
- 安裝孔徑:3MM
- 模塊尺寸:31*21*10.1MM(長*寬*高)
- 孔間距:15MM
- 模塊重量:4.3g
引腳說明
- 1. G -- Gnd(地)
- 2. V -- Vcc(電源+5V)
- 3. S -- Sign(信號)
應用示例
- 電路連接示意圖
- 磁控感測器模塊的 G、V、S分別連接 Arduino UNO的GND、VCC(+5V)、D7引腳。
- 示例代碼
// Reed Switch Test #define ledPin 13 //define LED pin #define reed_switchPin 7 //define reed switch Pin int reed_switchValue = 0; void setup() { pinMode(ledPin,OUTPUT); pinMode(reed_switchPin,INPUT); } void loop() { reed_switchValue = digitalRead(reed_switchPin); if(reed_switchValue == LOW) { digitalWrite(ledPin,HIGH); // detect the external magnetic field , set the LED on } else { digitalWrite(ledPin,LOW); // or set the LED off } }
程序下載地址:ReedSwitchTest
程序運行結果:當干簧管檢測到外部磁場後,內部彈片吸合,檢測到電平,點亮LED,否則熄滅LED。
參考資料
更多建議和問題歡迎反饋至 YFRobot論壇
購買方式:YFRobot 電子工作室