查看RTC 1307的源代码


[[Image:RTC-DS1307.jpg|350px|thumb|RTCDS1307模块]]


=== 产品简介 ===
<br>
RTC-DS1307时钟模块是一款基于I2C接口的实时时钟芯片DS1307而设计的模块，可用来计时。

DS1307串行实时时钟（RTC）是低功耗，全二进制编码的十进制（BCD）时钟/日历以及56字节的NV SRAM。地址和数据通过I2C双向总线串行传输。

时钟/日历提供秒，分钟，小时，日期，日期，月份和年份信息。对于少于31天的月份，将自动调整月末日期，包括闰年的更正。

带有AM / PM指示器的时钟以24小时或12小时格式运行。 DS1307具有内置的电源检测电路，可检测到电源故障并自动切换到备用电源。

当零件通过备用电源工作时，计时工作将继续进行。



=== 规格参数 ===
<br>
*供电电压：DC5V
*实时时钟（RTC）可以计算秒，分钟，小时，月份，月份，星期几和年份，并具有有效的闰年补偿，有效期至2100年
*56字节，电池支持的通用RAM，具有无限写入
*自动断电检测和开关电路
*在振荡器运行的情况下，电池备份模式下的功耗小于500nA
*工作温度：0℃～70℃
*安装孔径：3MM
*模块尺寸：45*19.5*6.5MM (长*宽*高)
*孔间距：14.5MM
*模块重量：5.2g



=== 应用示例 ===
<br>
'''电路连接'''
<br>
{|border="1" cellspacing="0" align="center" cellpadding="5" width="450px"
|-
|align="left"|'''RTCDS1307时钟模块'''
|align="left"|'''Arduino UNO'''
|-
|align="left"|VCC
|align="left"|+5V
|-
|align="left"|GND
|align="left"|GND
|-
|align="left"|SDA
|align="left"|SDA/A4
|-
|align="left"|SCL
|align="left"|SCL/A5
|}

'''电路连接示意图'''

[[Image:RTCDS1307连接示意图-arduino.png|800px|RTCDS1307模块连接示意图-arduino]]



:'''示例代码'''

<source lang="c">
/* arduino sketch -- arduino print date and time with ds1307 RTC breakout
   SETUP:
    arduino (UNO R3)     ds1307
      A4/SDA          →    SDA
      A5/SCL          →    SCL
      GND             →    GND

   Read More about DS1307: http://www.yfrobot.com.cn/wiki/index.php?title=RTC_1307

   BY YFROBOT
*/

#include <Wire.h>  // must be incuded here so that Arduino library object file references work
#include <RtcDS1307.h>

RtcDS1307<TwoWire> Rtc(Wire);

void setup () {
  Serial.begin(115200);

  Serial.print("compiled: ");
  Serial.print(__DATE__);      // 编译文档的日期
  Serial.println(__TIME__);    // 编译文档的时间

  //--------RTC SETUP ------------
  // if you are using ESP-01 then uncomment the line below to reset the pins to
  // the available pins for SDA, SCL
  // Wire.begin(0, 2); // due to limited pins, use pin 0 and 2 for SDA, SCL
  Rtc.Begin();

  RtcDateTime compiled = RtcDateTime(__DATE__, __TIME__); // 存储当前编译的时间及日期并打印
  printDateTime(compiled);
  Serial.println();

  if (!Rtc.IsDateTimeValid()) {
    if (Rtc.LastError() != 0) {
      // we have a communications error
      // see https://www.arduino.cc/en/Reference/WireEndTransmission for
      // what the number means
      Serial.print("RTC communications error = ");
      Serial.println(Rtc.LastError());
    } else {
      // Common Causes:
      //    1) first time you ran and the device wasn't running yet
      //    2) the battery on the device is low or even missing

      Serial.println("RTC lost confidence in the DateTime!");
      // following line sets the RTC to the date & time this sketch was compiled
      // it will also reset the valid flag internally unless the Rtc device is
      // having an issue

      Rtc.SetDateTime(compiled);
    }
  }

  if (!Rtc.GetIsRunning()) {
    Serial.println("RTC was not actively running, starting now");
    Rtc.SetIsRunning(true);
  }

  RtcDateTime now = Rtc.GetDateTime();  // 获取当前DS1307时间及日期
  if (now < compiled) {
    Serial.println("RTC is older than compile time!  (Updating DateTime)");
    Rtc.SetDateTime(compiled);
  } else if (now > compiled) {
    Serial.println("RTC is newer than compile time. (this is expected)");
    // Rtc.SetDateTime(compiled);
  } else if (now == compiled) {
    Serial.println("RTC is the same as compile time! (not expected but all is fine)");
  }
}

void loop () {
  if (!Rtc.IsDateTimeValid()) {
    if (Rtc.LastError() != 0) {
      // we have a communications error
      // see https://www.arduino.cc/en/Reference/WireEndTransmission for
      // what the number means
      Serial.print("RTC communications error = ");
      Serial.println(Rtc.LastError());
    } else {
      // Common Causes:
      //    1) the battery on the device is low or even missing and the power line was disconnected
      Serial.println("RTC lost confidence in the DateTime!");
    }
  }

  RtcDateTime now = Rtc.GetDateTime();  // 获取当前DS1307时间及日期
  printDateTime(now);   // 串口打印日期时间
  Serial.println();

  delay(10000); // ten seconds
}

#define countof(a) (sizeof(a) / sizeof(a[0]))

// 串口打印日期时间
void printDateTime(const RtcDateTime& dt) {
  char datestring[20];

  snprintf_P(datestring, countof(datestring), PSTR("%02u/%02u/%04u %02u:%02u:%02u"),
             dt.Month(), dt.Day(), dt.Year(),
             dt.Hour(), dt.Minute(), dt.Second() );
  Serial.print(datestring);
}

</source>

程序下载地址：[https://eyun.baidu.com/s/3c2hGJpY thermometer]


:'''串口监视结果'''
<br>
[[Image:LM35串口监视结果.png|center|LM35串口监视结果]]

===参考资料===
<br>
* [http://www.yfrobot.com/wiki/images/5/52/Lm35_datasheet.pdf LM35 数据参考手册] [https://eyun.baidu.com/s/3hr9IASs 备用地址]
* [http://www.datasheetcatalog.com/info_redirect/datasheet/nationalsemiconductor/DS005516.PDF.shtml 不同型号数据手册下载]


----


[[首页 | 返回首页]]

更多建议和问题欢迎反馈至 [http://www.yfrobot.com YFRobot论坛]

购买方式:[http://yfrobot.taobao.com/ YFRobot 电子工作室]


==Arduino 库==

[[RTC DS1307 DS3231库]]

==参考文档==


* [http://yfrobot.gitee.io/wiki/doc/DS1307.pdf DS1307芯片手册]





----


[[首页 | 返回首页]]

更多建议和问题欢迎反馈至 [http://www.yfrobot.com YFRobot论坛]

购买方式:[http://yfrobot.taobao.com/ YFRobot 电子工作室]